產品詳情
A11VO 泵設計用于開式回路中。-軸向柱塞元件的項目規劃、組裝和調試必須由合格人員進行。-工作管路油口和功能油口僅設計用于液壓管路。-運行期間及運行后不久，軸向柱塞元件 (是電磁鐵) 可能存在造成灼傷的風險。應采取適當?shù)拇胧?(例如穿著防 護服)。-根據軸向柱塞元件的不同工作狀態 (工作壓力、油液溫度)，特性可能會改變。-壓力油口：油口和固定螺紋設計用于規定壓力。機器或系統制造商必須確保連接元件和管路的系數滿足規定的工作條件 (壓力、流量、液壓油、溫度)。-此處包含的數據和說明必須遵循。-采用以下緊固扭矩：·軸向柱塞元件的螺紋孔： 圖片} 軸承是不是磨損松動(主張?zhí)鎿Q新的軸封及軸承),替換時應當心,主張用外徑與軸封共同(軸封用)和外徑稍大于軸承內徑,內徑稍大于泵軸外徑(軸承用)的平坦硬物將它們送到固定方位上,避免軸封變形和損壞軸承,3,整同心度后在設備. 避免***,安裝和調試說明調試和運行期間,必須向泵殼體注油,必須在低速,無負載狀態下進行調試,直至系統脫氣如果長時間靜止不動,殼體會通過維修管路漏油,重新啟動時,必須向泵殼體重新注入油,吸油口S處的入口壓力不能低于0.
A11VO40系列
A11VO40LRDH1/10R-NZC12K02
A11VO40DR/10R-NSC-12N00
A11VO40DRG/10R-NPC12N00
A11VO60系列
A11VO60DRS/10R-NZC12N00
A11VO60DRS/10L-NZC12K07
A11VO75系列
A11vo75LRDS/10R-NSD12N00-S
A11VO75LR3S/10R-NZD12N00
A11VO75LRDS/10R-NSD12N00-S
A11VO95系列
A11VO95LRDS/10R-NSD12N00
A11VO95EP2D/10R-NSD12K02H
A11VO95SLRDS/10R-NZD12K82
A11VO130系列
A11VO130DR/10R-NZC12K07
A11VLO130DRS 10R-NPD12N00
A11VO130LRDS/10R-NSD12K01-S
A11VLO130LRS/10R-NZG12K01
A11VO130LRDS/10R-NZD12K61
A11VO130LRDS+A11V0130LRDS
A11VLO130LRDS/10R-NSD12K02
A11VLO130LRDU2/10R-NZD12K02P-S
A11VO130LRDS/10R-NZD12K61 + A11VO60LRDS/10R-NZC12N00
A11VO145系列
A11VO145LRDS/11L-NZD12K82
A11VO145LRDS/10L-NZD12N00
A11VO145LRDS/11R-NZD12N00
A11VO145LRDS/11R-NPD12N00
A11VO145LRDS/11R-NZD12K83
A11VO14SLRDS/11L-NZD12K83
A11VO14SLRDS/11L-NZD12N00
A11VO145LRDS/11R-NZD12K07
A11V145LRDS+A11V95LRDS
A11VO145LRDS/10L+A11V0130LRDS/10L
A11VLO190系列
A11VO190DR/10R-NPD12N00
A11VO95DRS/10R-NSD12N00
A11VO190DRS/11R-NZD12K84
A11VO190DRG/11R-NPD12N00
A11VO190DRG/11R-NTD12N00
A11VO190LRD/11R-NPD12N00
A11VLO190LRDS/11L-NSD12N00
A11VLO190LRDS/11R-NSD12K07
A11VLO190LRDS/11R-NZD12K83+A11VO130LRDS/10R-NZD12K61+A11VO60DRS/10R-NZC12N00
A11VLO190LRDU2/11R-NZD12KO2P-S
A11VO190LRDH2/11R-NZD12K01+AZPF-1X/19R
11VLO190+A11VLO130+A11VO60
A11VLO190LRDH2
A11VLO260系列
A11VO260LRDH2/11
A11VO260DRG/11R-NPD12K04-K
A11VLO260LRDU2/11R-NZD12K02P-S
A11VLO260DRS/11R-NZD12N00
A11VLO260DRG/11R-NPD12NOO
